THE WHITEWING
EWW-180
EWW-180 also known as the Whitewing is the evolution of The Blackwing. This model is powered by a propeller that will give you a greater efficiency making this version ideal for long autonomous travels or long range FPV flight. Nevertheless you can also get the EDF version. Both versions can be interchanged because the wing is detable thanks to an innovative and totally 3d printed locking mechanism patented by Eclipson Airplanes, the system is as simple as effective and the airflow will ensure that the latch is closed during the flight. The aerodynamic has been improved mainly thanks to the use of a nonlinear wing torsion, a higher aspect ratio and a lower static margin that was possible due to the use of winglets, this airplane reaches the impressive glide ratio of 19 to 1 at 40 km/h (PLA version). This means that the aircraft can not be used only like UAV/FPV model but also like a motor glider.
Includes:
-STL files
-G-codes for PLA and LW-PLA
-Decal scheme
For free:
-Model for Real Flight simulator
€33
Features:
-FPV/HD camera ready.
-Detachable wing
-Replaceable fixed tricycle landing gear
-Steerable nose gear.
 |  |  |  |  |
|---|---|---|---|---|
 |  |  |  |  |
 |  |
ASSEMBLY GUIDE
SHOPPING LIST
ALL THE COMPONENTS THAT YOU HAVE TO BUY TO FLY THE AIRPLANE
FILAMENT
QUANTITY - 350g (LW-PLA) 650g (PLA or PETG)
TYPE - LW-PLA , PLA or PETG
(Other materials can be used for category C parts)
ECLIPSON STANDARD POWER PACK
SERVOS NEEDED - x3
PROPELLER - (do not use prop bigger than 7 inches in case you want to use the landing gear)
​
Recommended
BATTERY
VOLTAGE - 11,1V (3S) or 7,4V (2S)
CAPACITY - 1500 mAh to 2200 mAh
DISCHARGE - >20C
​
Proposed:
PLA: BAT3
LW-PLA: BAT2
​
OTHER PARTS
-PUSH RODS - D1,2mm (min length 60mm) 3units
-SERVO LEAD EXTENSION (min 400mm) 2 units
-BOLT- M3X14mm 4units
-TAPE
-SCREW - M2X8mm (aprox) 32 units
-VELCRO
-PUSH RODS CONNECTORS (Not mandatory) 3units
-GLUE - cyanoacrylate + accelerator(not mandatory)
-WIRE - 0,5 mm
-RUBBER BAND (Necessary only if you use the landing gear)
-STEEL ROD - D2mm (Length 100mm) 2units
(Necessary only if you use the landing gear)
-STOP COLLARS D2,1mm 6units
(Necessary only if you use the landing gear)
-CARBON FIBER TUBE - D6x4mm (Length 500mm) 4units
-CARBON FIBER TUBE - D4x3mm (Length 400mm) 2units
Recommended
FPV/UAV COMPONENTS
THE FOLLOWING COMPONENTS ARE NOT MANDATORY TO FLY THE AIRPLANE
FLIGHT CONTROLLER
Proposed - Matek Systems F411-WING
or Matek Systems F405-WING
VTX and ANTENNA
​
Proposed - Matek 5.8G 40CH 25/200/500mW
and Realacc Pagoda RHCP Antenna 65mm 5.8G
TUTORIALS
In case you don´t have previous experience with drones /FPV planes the following tutorials will help you to understand how to properly set up your flight controller using Inav or Arduplane.
Inav is preferred over Arduplane for beginners due to its simplicity , nevertheless arduplane is a more powerful tool especially to plan way point mission.
USING ARDUPLANE
In case you decide working with arduplane use the recommended Matek Systems F405-WING because F411 is not compatible.
