MXS-R

3D printed version of Nigel Lamb´s MXS-R.
This is a versatile model that can be used like as sports, race  or aerobatic plane, compatible with PLA/PETG or LW-PLA, by choosing one or the other material the flight characteristic will be different. In the case you choose LW-PLA the airframe will be more optimized (read more), you will get the same wing loading, therefore the same agility and in general the flight characteristic of an equivalent model made with balsa wood or foam, but of course for a much lower price! If you chose PLA/PETG, you will enjoy a great racer, the extra inertia will give more stability at higher speeds. You don´t know which material to choose? Just print both because the cost is ridiculous! 

Includes:
-STL files
-Decals (Breitling Scheme)

-G-codes for PLA and LW-PLA
For free:

-Cura profiles

-FPV kit
-Complete left wing for testing

€35

Features:
-Racer/ Aerobatic

-Light and strong

-Modular design

-2 main landing gears options

4
6
10
2_edited
7
5
8
11
2
3
1
9

SPECIFICATIONS

                                    LW-PLA    PLA
PRINTED WEIGHT              550gr   950gr

TAKE OF WEIGHT             1200gr  2000gr
STALL SPEED                   26kmh  32kmh
MAX LOAD FACTOR            20G      30G

WING LOADING                              42g/dm²    71/gr/dm² 

WING SPAN               1,350mm (53")

WING SURFACE          28dm2

WING ASPECT RATIO   5,5
WING AIRFOIL            SYMETRIC
LENGTH                     1040mm

ARRANGEMENT DRAWING AND PRINTING PARAMETERS

ASSEMBLY GUIDE

SHOPPING LIST

ALL THE COMPONENTS THAT YOU HAVE TO BUY TO FLY THE AIRPLANE

3D PRINTER

MIN PRINTING VOLUME - 210x210X205 (X,Y,Z)
NOZZLE DIAMETER - 0,4 mm

Recommended

FILAMENT

QUANTITY - 550gr (LW-PLA) or 950gr (PLA or PETG)


Recommended

MOTOR

KV-  800 to 1200

MAX POWER -  300 to 1000 watts

DIAMETER - 35mm

VOLTAGE - Up to 14,8V (4S)

HOLES - As shown in the drawing

Proposed

SunnySky X2814 900KV

ESC

CURRENT - 50A

VOLTAGE -  Up to 14,8V (4S)

Proposed
Aerostar 50A

BATTERY

VOLTAGE - up to 14,8V (4S)

CAPACITY - 2000mAh to 2600 mAh

Proposed
Turnigy Nano-Tech 2200mAh 4S

 

*If printed with PLA/PETG it is recommended to use two batteries connected in parallel with XT60 Harness in order to balance the plane.

PROPELLER

FOR 900KV - 11x5.5

FOR 1200KV - 9X6

Proposed:
Propeller knife horse paddle

SERVOS (x5)

CATEGORY - Micro servo 9g

VOLTAGE - 4,8V to 6V

Proposed - Turnigy™ TG9e

RADIO CONTROL SYSTEM

MIN CHANNELS - 5CH

Proposed - flysky fs-i6x (with i6X-iA6B receiver)

OTHER PARTS

-CARBON FIBER TUBE - D8x6mm (length 500mm) 4units (2 units for PLA version)
-CARBON FIBER TUBE - D4x2mm (length 400mm) 2units (Not required for PLA version)
-STEEL ROD - D3mm (Length 400mm) 2units
-STEEL ROD - D2mm (Length 100mm) 2 units
-PUSH RODS - D1,2mm (Length 500mm)  3units

-BOLT - M3X25mm (with nuts and washers)  4units

-SCREW - M2X8mm 18units

-VELCRO

-GLUE - cyanoacrylate + accelerator
-SERVO LEAD EXTENSION (min 100mm) 2 units
-
PUSH RODS CONNECTORS  5units 
-RUBBER BAND

-WIRE - 0,5 mm

Main landing gear option1:

-SPONGE WHEEL  2units (Alternatively you can 3D print this part)

    Diameter 40mm

    Wide 10,5mm

    Inner hole D2mm

-STOP COLLARS D2,1mm  2units

Main landing gear option2:
 -SPONGE WHEEL  2units (Alternatively you can 3D print this part)
    Diameter Free

    Wide Free

    Inner hole D3mm   

 -STOP COLLARS D3,1mm  4units   

Tail landing gear:
 -SPONGE WHEEL  1units (Alternatively you can 3D print this part)
    Diameter 20 to 30 mm

    Wide Free

    Inner hole D2mm   

 -STOP COLLARS D2,1mm  1units 

Eclipson 3d printed aircraft
  • Eclipson youtube
  • 3d printed plane instagram
  • Facebook eclipson
© 2020 Eclipson Airplanes. All Rights Reserved.
Madrid, Spain
Terms & condition / Privacy policy / Refund policy / Fulfillment policy
0

MY CART